Single Turbo G35 coupe by Eternal Motorsports

[damen]

Four months ago my car was sent to Eternal Motorsports in Connecticut to be fitted for a single turbo set up for the 2003 G35 coupe. I’ve had my car back now for about a month. Parts for this kit include:
-Garrett GT35R turbo (dual ball bearing turbo)
-Twin Spearco intercoolers
-Tial 44mm waste-gate with a .5Bar (7.25 psi) spring (with a recirculating setup) -this is good for 8.5 psi. of boost
-3” down pipe leading to the stock muffler
-High flow cat
-MAP-ecu for fuel management
-440cc injectors
-K&N filtered (wet sock) cold air intake
-Walbro 255 fuel pump with a return fuel system

The car runs fine and has power that doesn’t seem to stop. As of right now the kit is using the MAP-ecu for fuel management but over the next couple of weeks Eternal Motorsports will be looking to install the Uni-Chip system with a plug and play set up on my car. This will be for those that may want more boost as well as being able to control some timing if needed. The MAP-ecu will still be available as a tuner set up.

Attached I have some pics of the kit as well as a dyno sheet. You’ll see that the dyno was on a Mustang Dyno but, once the Uni-Chip and is installed and tuned we’ll be going to a Dyno-Jet Dyno for those that may want to see numbers on it. At 8.94 psi. of boost my car made 392-hp. and 416 ft. tq.

MSRP of the kit is estimated at $6,300. Tuner kits will be available without any fuel or engine management system.

In addition to the kit my car has an ACT clutch, Greddy boost controller, and Zeitronix gauge.

Pics included: http://www.imagestation.com/album/index.html?id=2121101314

If anyone would like to see the kit in person, I'm planning on go to the AAM this weekend Oct. 1st.

[revhighG35]

can't get the link to work ???

[G35fromPA]

Wow...8.5 psi of boost is a lot for stock internals, no?

[limits_at_infiniti]

nice ... find out if they need a stock g35 sedan AT to test out as well ::wink, wink::

[Dr_Dave]

Wow. More torque than hp. http://forums.freshalloy.com/images/graemlins/laugh.gif

[PullingMaxGs]

Damen,
Are you the same Damen that knows Carlton (in MD)? If so, try and make my 15 Oct FX/Coupe/Nissan meet in Columbia - - I'll provide more specifics later...

[damen]

can't get the link to work ???



try the link now. i think i fixed it.

[damen]

Wow...8.5 psi of boost is a lot for stock internals, no?



no 8.5 isn't bad because if you figure there are some kits making 9psi. and i've even seen a G35 coupe making 11psi. on stock internals. once Eternal Motorsports changes my car over to the Uni-chip i should be making somewhere around 10psi. on stock internals. http://forums.freshalloy.com/images/graemlins/grin.gif

[damen]

nice ... find out if they need a stock g35 sedan AT to test out as well ::wink, wink::



where are you located at? they are located in Conn. i'll mention that to them.

[damen]

Wow. More torque than hp. http://forums.freshalloy.com/images/graemlins/laugh.gif



yes and trust me it takes off. lovely feeling. http://forums.freshalloy.com/images/graemlins/grin.gif pinning you to the seat.

[damen]

Damen,
Are you the same Damen that knows Carlton (in MD)? If so, try and make my 15 Oct FX/Coupe/Nissan meet in Columbia - - I'll provide more specifics later...



yeah that's me http://forums.freshalloy.com/images/graemlins/grin.gif carlton told me about it. i will definitely try and make it. by then i should have my Uni-chip in and making more boost. http://forums.freshalloy.com/images/graemlins/grin.gif can't wait.

[Eagle1]

It sounds terrific. But please be careful if you are running on stock guts. Anything over 400hp and you are on the thin edge of tolerances. If you run 10psi I don't thing you are going to have the ability to repeatedly and reliably go there without breaking a rod or holing the block. Nobody else has done it.....

[Riffster]

Damen -

It's great to read that you're getting that kind of performance but I have to echo what Eagle1 has written - you'll only get away with that kind of PSI for just so long on an aluminum block like that of the VQ35DE. You might want to dial that back a bit - and re-tune of course when you do.

That being said - have fun and keep it safe.

- Riff

[damen]

well since i have the boost controller. i will have a low setting and a high setting. low will probably be at 6psi. and high will probably be at 10psi. with that being said i could just change boost settings and still be safe. i would drive around on 6psi. and when needed i would adjust to 10psi. http://forums.freshalloy.com/images/graemlins/grin.gif

[opimax]

But what if you get a ticket? http://forums.freshalloy.com/images/graemlins/wink.gif

Mark

[damen]

i'd either pay it or go to court. just like everyone else. http://forums.freshalloy.com/images/graemlins/rolleyes1.gif http://forums.freshalloy.com/images/graemlins/grin.gif

[PullingMaxGs]

Damen,
Are you the same Damen that knows Carlton (in MD)? If so, try and make my 15 Oct FX/Coupe/Nissan meet in Columbia - - I'll provide more specifics later...



yeah that's me http://forums.freshalloy.com/images/graemlins/grin.gif carlton told me about it. i will definitely try and make it. by then i should have my Uni-chip in and making more boost. http://forums.freshalloy.com/images/graemlins/grin.gif can't wait.



Damen,
Look forward to meeting you (and the Coupe) - I'm providing the hotdogs, burgers, and heated pool. Asking all to bring 'canned' beverage of choice. We'll kick-off at 1 p.m. More specifics later!!!!

Claude

[damen]

yeah i'm planning on being there.

[limits_at_infiniti]

nice ... find out if they need a stock g35 sedan AT to test out as well ::wink, wink::



where are you located at? they are located in Conn. i'll mention that to them.



Im not to far from CT, I am located in NY by the 95.

[PullingMaxGs]

yeah i'm planning on being there.



Ok, Chief - - I'll save you a spot (if I can)!!! http://forums.freshalloy.com/images/graemlins/smile.gif

But...won't be much room left after Carlton parks that huge Aramada... http://forums.freshalloy.com/images/graemlins/smile.gif

[damen]

that's cool. just pm me the details.

[palmerwmd]

Damen,
Are you the same Damen that knows Carlton (in MD)? If so, try and make my 15 Oct FX/Coupe/Nissan meet in Columbia - - I'll provide more specifics later...



yeah that's me http://forums.freshalloy.com/images/graemlins/grin.gif carlton told me about it. i will definitely try and make it. by then i should have my Uni-chip in and making more boost. http://forums.freshalloy.com/images/graemlins/grin.gif can't wait.



Damen,
Look forward to meeting you (and the Coupe) - I'm providing the hotdogs, burgers, and heated pool. Asking all to bring 'canned' beverage of choice. We'll kick-off at 1 p.m. More specifics later!!!!

Claude



Were is this meet?

I live in MD half of the time.
If you check my sig maybe we'll do some "performance comparison"

Fred.. http://forums.freshalloy.com/images/graemlins/laugh.gif

[damen]

sounds good to me but, i'm not hosting the meet.

[damen]

well i'll be heading up to east harford, conn. either tonight or tomorrow morning. the Uni-chip will be installed and tuned at XXTuning. i'm hoping for 400hp. i really don't need much more than that. i think they are going to tune for two maps 6psi and 10psi. of boost. i know that they are going to tune on a dynapak but, they have a mustang dyno also. wish me luck guys.