New member

[Koopa Troopa]

I had a T04S Silvia awhile back and had planned on being more active but I got angry at the car, ran into some problems getting it to run and instead of just replacing some wiring harnesses I stripped the car, junked it and bought a couple of cars inbetween and forgot about this forum.

http://i21.photobucket.com/albums/b267/koopatroopa187/Sillbeer%20S14/CRW_0615.jpg
http://i21.photobucket.com/albums/b267/koopatroopa187/Sillbeer%20S14/LD8A6786.jpg
http://i21.photobucket.com/albums/b267/koopatroopa187/Sillbeer%20S14/LD8A6798.jpg
http://i21.photobucket.com/albums/b267/koopatroopa187/Sillbeer%20S14/LD8A6797.jpg
http://i21.photobucket.com/albums/b267/koopatroopa187/Sillbeer%20S14/LD8A6841.jpg
http://i21.photobucket.com/albums/b267/koopatroopa187/Sillbeer%20S14/LD8A6862.jpg
http://i21.photobucket.com/albums/b267/koopatroopa187/Sillbeer%20S14/LD8A6869.jpg

I really regret the impulse decision I made and wish I had just pushed it outside, went to Nissan and ordered a new engine harness/ accessory harness and dumped the turbo set up for a sick NA set up.

However I then bought this sweet car for $1k

1989 Suzuki Alto Works RS/R
http://i21.photobucket.com/albums/b267/koopatroopa187/26%20May%20RCCA%20Auto%20X/LD8A6933.jpg
http://i21.photobucket.com/albums/b267/koopatroopa187/Alto%20Works/LD8A7059.jpg
http://i21.photobucket.com/albums/b267/koopatroopa187/Alto%20Works/LD8A7054.jpg

Ended up bending the frame and buying a Honda Civic SiR which is the last car I'll be buying for awhile.

http://i21.photobucket.com/albums/b267/koopatroopa187/The%20Civic/download2.jpg

Car had some decent parts on it when I bought it but I've done a bit of work to it since then.

Engine Parts
*Top Fuel intake (J's Racing knock off)
*Unkown Jasma header
*Test pipe
*Spoon mid pipe
*No make trumpet muffler
*Mugen LSD
*'98 Spec DC2R transmission with 4.78 final drive.
*Fidanza 7lbs flywheel
*6 puck clutch
*Spoon VC3E VTEC controller

Suspension
*Cusco Zero 1 dampers
*Like 94.7% of the bushings are poly bushings from *Suspension Techniques
*Cusco front lower arm bar
*Unknown rear lower arm bar
*Unknown rear frame bar thing
*Hyakusiki C pillar bar
*Spoon rear strut tower bar
*EK9 front strut tower bar
*J-Speed fender braces

Brakes, Wheels, Tires
*Brig medium rally pads
*Feels brake master cylinder brace
*Racing Gear brake lines
*Racing Gear rotors
*Mugen RNR 15x6.5 +45 wheels
*Falken RT615 205/50/15

Interior
*Recaro Pro Racer SPG
*Nardi 330mm Deep Corn steering wheel
*Juran steering spacer
*Spoon titanium shift knob
*Relocated ECU to glovebox

Exterior
*Spoon carbon fiber front lip
*Varis carbon hood
*Spoon carbon fiber rear wing

Parts not on car
B18C5 block - Awaiting a chipped ECU and should install in November

Future mods
8 point rollcage with door bars
Gut it
Thinking about installing my Stack ST8905 cluster

Anyways I am really just making this thread because I'm a new member trying to sell a Motec ECU and I wanted people to know where I stand.

http://forums.freshalloy.com/showthread.php?t=187603